MikroTik RouterOS v7 Route Filters
MikroTik RouterOS v7 Commonly Used FiltersNotes about using the filers Commonly Used Filters for OSPF Commonly Used Filters for RIP
Mikrotik showing only 1 single line of log messages !
Question: I am not able to determine why my Mikrotik box shows only a single line of log information.I checked all of the configuration, and everything appears to be in order. Answer: Execute this to revert to default config:
GRE Configuration Between Mikrotik And Cisco Router
CiscoRouter Configuration: R1>enable R1#conf t R1 (config)# hostname CiscoRouter CiscoRouter (config)# interface FastEthernet0/0 CiscoRouter (config-if)# ip address 104.10.1.2 255.255.255.252 CiscoRouter (config-if)#no shutdown CiscoRouter (config-if)#exit CiscoRouter (config)# interface FastEthernet0/1 CiscoRouter (config-if)# ip address 172.16.2.1 255.255.255.0 CiscoRouter (config-if)# no shutdown CiscoRouter (config-if)# exit CiscoRouter (config)# interface tunnel 0 CiscoRouter (config-if)# ip ip address 192.168.1.2 255.255.255.252 CiscoRouter (config-if)# …
GRE Configuration Between Mikrotik And Cisco Router Read More »
How to block specific IP address at Mikrotik?
Step-by-step guide Follow these steps to add filter rule using Winbox:
Huwaei GPON OLT LACP (Link Aggregation) Command
link-aggregation 0/2 (MCU Card Number) 0 ( Interface Number) egress-ingress port vlan (As per your Requierment ) 0/2 0 link-aggregation add-member 0/2/0 0/2 1 > (Which interface you want to add at link-aggregation port) link-aggregation 0/2 0 egress-ingress port vlan (As per your Requierment ) 0/2 0 link-aggregation add-member 0/2/0 0/2 1
How To Reset Switch Port – Cisco switch?
Command : 1st go-to global configuration mode then ” default >interface name<
PL2303HXA Phased out since 2012. Please contact your supplier (SOLVED)
Some Cheap Chinese FTDI cables use a fake chipset from Prolific. Prolific has prohibited the use of these cables. Windows does detect them but they are not usable. Use these 8 easy steps to install the driver. . To solve this, you can download the driver …
PL2303HXA Phased out since 2012. Please contact your supplier (SOLVED) Read More »
VSOL OLT LACP With Mikrotik (Bonding)
Mikrotik End /interface bonding add name=bonding slaves=ether11,ether12 At Vsol End LACP Configuration: epon-olt(config)# channel-group 1 mode static epon-olt(config)# channel-group 1 load-balance smac epon-olt(confit)# interface gigabitethernet 0/1 epon-olt((config-pon-0/1)# channlel-group 1 epon-olt(config)# interface gigabitethernet 0/2 epon-olt((config-pon-0/1)# channlel-group 1 Mikrotik
VLAN BASED BANDWIDTH CONTROL IN BDCOM SWITCH
step – ১: প্রথমে আমাদের একটা policy-map তৌরী করতে হবে। এজন্য আমাদের config mode এ যেতে হবে। তারপর কম্যান্ড লিখতে হবেSw_config#policy-map testএখানে test হচ্ছে নাম। policy-map এর একটা নাম দিলাম।step -২:এবার আমাদের আমাদের কাঙ্ক্ষিত vlan টা দেখিয়ে দিবো। এজন্য আমাদের নিচের কমান্ডটা দিতে হবে।Sw_Pop-policy-map#classify vlan 3000step -৩:step ৩ হচ্ছে last step , এখানেই আমাদেরকে কত …